Audio-Technica AT-OC9XEN

Ga over de afbeelding met je muis om een vergroting te zien

346,00
(Incl. BTW)
Voorraad
+
AT-OC9XEN

Dual moving coil stereo cartridge with Elliptical nude stylus

  • Features low mass nude elliptical stylus and aluminium cantilever
  • A neodymium magnet and pure iron yoke provide increased magnetic energy
  • Features threaded inserts in the cartridge body
  • Aluminium body minimizes unwanted vibration for reduced resonance
  • PCOCC is used for the coils to achieve pure signal transmission

AT-OC9XEN

The next Generation of the legendary OC9 cartridge series

Since its introduction more than 30 years ago, Audio-Technica’s pioneering moving coil OC9 cartridge series has been prized by demanding vinyl listeners and professional critics alike for its musical transparency, expression of sound and precise construction. Featuring a square shank for accurate stylus alignment and nude diamond for increased fine detail retrieval.

  • Features low mass nude elliptical stylus and aluminium cantilever
  • A neodymium magnet and pure iron yoke provide increased magnetic energy
  • Threaded inserts in the cartridge body enable the cartridge to be mounted on to the headshell or integral tonearm with just two screws – no nuts required 
  • Aluminium body minimizes unwanted vibration for reduced resonance and a superior audio reproduction
  • Pure Copper by Ohno Continuous Casting process (PCOCC) is used for the coils to achieve the purest signal possible

Elliptical Nude Stylus

Elliptical diamond stylus follows the groove modulation with greater precision compared to a conical stylus, offering improved frequency and phase responses whilst reducing distortion.

Easy mounting

Threaded holes in the cartridge body enable the cartridge to be mounted on to the headshell, or integral tonearm, with just two screws M2.6 – no nuts or bolts required.

Aluminium Body

Aluminum body minimizes unwanted vibration for reduced resonance and superior audio reproduction

Made in Japan

Produced in the Audio-Technica Fukui factory in Japan under strict quality control for precise manufacturing.

Model AT-OC9XEN
Bevestiging 1/2” centers / Threaded inserts
Frequentierespons 20 - 30,000 Hz
Materiaal behuizing Aluminium
Kanaalscheiding 25 dB (1 kHz)
Balans uitgangskanaal 1.5 dB (1 kHz)
Uitgangsspanning 0.35 mV (at 1 kHz, 5 cm/sec)
Verticale trackinghoek 20 degrees
Bereik verticale trackingskracht 1.8 to 2.2 g (standard 2.0 g)
Naaldvorm Elliptical Nude
Naaldgrootte 0.3 x 0.7 mil
Naaldconstructie Nude square shank
Cantilever Aluminium pipe
Spoelimpedantie 12 Ohms (1 kHz)
Spoelinductantie 25 μH (1 kHz)
Gelijkstroomweerstand 12 Ohms
Statische compliantie 20 x 10 – 6 cm / dyne
Dynamische compliantie 9 x 10 – 6 cm / dyne (100 Hz)
Aansluitpennen Brass
Spoeldraad PCOCC (Copper by Ohno Continuous Casting process.)
Aanbevolen ladingsimpedantie Min 100 Ohms
Elementgewicht 7.6 g
Afmetingen 17.3 (H) x 16.8 (W) x 25.7 (L) mm
Meegeleverde accessoires 1 non magnetic screw driver
1 brush
2 washers
4 pairs of mounting screws: 5mm, 8mm, 10mm, 12mm
1 plastic protector

Specificaties

 

Snelle levering

Wij leveren over heel de wereld

Gratis bezorging

vanaf €100,- binnen Nederland en naar België

Hoge kwaliteit producten

Wij leveren alleen producten waar wij vertrouwen in hebben.